Toyota Key Programmer

This adapter can be used to read the PIN code of the
transponder key automatically, and write the PIN code
into the computer transponder of the suited ECU. It can
be used to match the vehicle without keys and needn't
change any computer when matching. Be suitable for all
the Toyota series from 1997 to 2005.

. Be suitable for the wafer key's match of Toyota, such
  as Lexus (LS400, ES300, GS300, IS2000, IS300), Camry
  2.0, 2.4, Jeep 2007, 3400, 4500, 4700, Cavalon, Previa.
. Equip English using manual. Offer technology support.
. From the date of purchase, we provide for a 18 month
  repair warranty with conditions.

Use for the following cars:
. ES300 (1997-2003)
. GS300 (1997-2003)
. GS400 (1997-2000)
. GX430 (2001-2003)
. IS300-IS200 (2001-2003)
. LS400 (1997-2000)
. LX470 (1998-2002)
. RX300 (1999-2003)
. SC300 (1998-2001)
. SC400 (1998-2001)
. 4Runner (1999-2003)
. Avalon (1998-2003)
. Cammry-4cly (1998-2005)
. HighLander (2001-2003)
. Lander Cruiser (1998-2003)
. MR2 (2000-2003)
. RAV4 (2000-2003)
. Sequoia (2000-2003)
. Sienna (1998-2003)
. Solara (1999-2003)
. Previa (1999-2003)

Operations of key programmer:
. Dismantle the engine ECU from the vehicle (or IMMO),
  and take down the IC chip identified as "93C56" (fixed
  to the computer in the vehicle engine, for the Camry
  being IC601, and Lexus being IC900. Identification
  number for a chip fixed to IMMO is 93LC66). Clean up
  every pin of IC to make sure of a sound connection.
. Install 93C56 on the device through programmer, make
  sure that the connection is good.
. Supply electricity to the programmer, the screen will
  show "can work normal" with a beep sound indicating
  that the machine is working well.
. Press "R-key", and the red light "LED" will be lit,
  programmer is thus ready for programming.
. Put the key on the key logo of the programmer.
. Press "R-key" again to hear the beep sound beep 4
  times, and the red light also goes off, these means
  that the key has been successfully programming to the
  programmer. If the beep sound is not made 4 times,
  then repeat the operation until you hear the exact 4
  beep sound.
. By the stated operations you can programming 3 keys to
  the programmer altogether.
. Now you can verify whether the 3 keys have been
  actually programmed: press "R-key", put a key near the
  key logo, if a 4-beep sound is made, that means the
  programming is effective. Every key must be verified so
  that they can be program to 93LC56 and 93LC66.
. Press Pr-A, Pr-B and Pr-C orderly to programming the
  3 programmed keys to 93C56(or 93LC66). When "Ok"
  displays, the programming succeeds; otherwise "Error"
  signal appears. Failure may be due to misconnection
  between 93C56 and the programmer, or the reverse
  installation or corruption of the chip.

For more information about this product, please contact
us freely.

1. Well and High Quality Control
2. Prompt Delivery
3. New Product
4. Customer's Designs and Logos are Welcome
5. Competitive Prices
6. Small Order Acceptable
7. OEM Accepted

toyota key programmer, key programmer, toyota key, auto key programmer, car key programmer